Biopolymeric Anticorrosion Coatings from Cellulose Nanofibrils and Colloidal Lignin Particles

dc.contributorAalto-yliopistofi
dc.contributorAalto Universityen
dc.contributor.authorDastpak, Armanen_US
dc.contributor.authorAnsell, Philipen_US
dc.contributor.authorSearle, Justin R.en_US
dc.contributor.authorLundström, Marien_US
dc.contributor.authorWilson, Benjamin P.en_US
dc.contributor.departmentDepartment of Chemical and Metallurgical Engineeringen
dc.contributor.groupauthorHydrometallurgy and Corrosionen
dc.contributor.organizationSwansea Universityen_US
dc.date.accessioned2021-10-13T06:53:11Z
dc.date.available2021-10-13T06:53:11Z
dc.date.issued2021-09-01en_US
dc.descriptionThis research was funded by Technology Industries of Finland/Jane and Aatos Erkko Foundations “Future Makers: Biorefinery Side Stream Materials for Advanced Biopolymer Materials (BioPolyMet)” and Academy of Finland (NoWASTE, no. 297962). Furthermore, this work utilized facilities provided by the RawMatTERS Finland Infrastructure (RAMI) at Aalto University, supported by the Academy of Finland. Additionally, we are grateful for the support by the FinnCERES Materials Bioeconomy Ecosystem. The authors would like to express their gratitude to Jari Aroma for providing expertise on EIS, Antti Markkula and Pasi Väisänen (SSAB Europe Oy) for providing the HDG substrates, and Ville Saarimaa (Top Analytica Oy) for assistance with further characterization of the coatings. Publisher Copyright: © 2021 The Authors. Published by American Chemical Society.
dc.description.abstractThis study presents a process for preparation of cellulose-lignin barrier coatings for hot-dip galvanized (HDG) steel by aqueous electrophoretic deposition. Initially, a solution of softwood kraft lignin and diethylene glycol monobutyl ether was used to prepare an aqueous dispersion of colloidal lignin particles (CLPs) via solvent exchange. Analysis of the dispersion showed that it comprised submicron particles (D = 146 nm) with spherical morphologies and colloidal stability (ζ-potential = -40 mV). Following successful formation, the CLP dispersion was mixed with a suspension of TEMPO-oxidized cellulose nanofibers (TOCN, 1 and 2 g·L-1) at a fixed volumetric ratio (1:1, TOCN-CLPs), and biopolymers were deposited onto HDG steel surfaces at different potentials (0.5 and 3 V). The effects of these variables on coating formation, dry adhesion, and electrochemical properties (3.5% NaCl) were investigated. The scanning electron microscopy results showed that coalescence of CLPs occurs during the drying of composite coatings, resulting in formation of a barrier layer on HDG steel. The scanning vibrating electrode technique results demonstrated that the TOCN-CLP layers reduced the penetration of the electrolyte (3.5% NaCl) to the metal-coating interface for at least 48 h of immersion, with a more prolonged barrier performance for 3 V-deposited coatings. Additional electrochemical impedance spectroscopy studies showed that all four coatings provided increased levels of charge transfer resistance (Rct) - compared to bare HDG steel - although coatings deposited at a higher potential (3 V) and a higher TOCN concentration provided the maximum charge transfer resistance after 15 days of immersion (13.7 cf. 0.2 kΩ·cm2 for HDG steel). Overall, these results highlight the potential of TOCN-CLP biopolymeric composites as a basis for sustainable corrosion protection coatings.en
dc.description.versionPeer revieweden
dc.format.extent12
dc.format.extent41034-41045
dc.format.mimetypeapplication/pdfen_US
dc.identifier.citationDastpak, A, Ansell, P, Searle, J R, Lundström, M & Wilson, B P 2021, ' Biopolymeric Anticorrosion Coatings from Cellulose Nanofibrils and Colloidal Lignin Particles ', ACS Applied Materials and Interfaces, vol. 13, no. 34, pp. 41034-41045 . https://doi.org/10.1021/acsami.1c08274en
dc.identifier.doi10.1021/acsami.1c08274en_US
dc.identifier.issn1944-8244
dc.identifier.issn1944-8252
dc.identifier.otherPURE UUID: 2c3587ac-60d2-4dbb-9e0f-3280f56e2520en_US
dc.identifier.otherPURE ITEMURL: https://research.aalto.fi/en/publications/2c3587ac-60d2-4dbb-9e0f-3280f56e2520en_US
dc.identifier.otherPURE LINK: http://www.scopus.com/inward/record.url?scp=85114430084&partnerID=8YFLogxKen_US
dc.identifier.otherPURE FILEURL: https://research.aalto.fi/files/68023833/CHEM_Dastpak_et_al_Biopolymeric_Anticorrosion_Coatings_2021_ACS_Appl_Mater_Interfaces.pdfen_US
dc.identifier.urihttps://aaltodoc.aalto.fi/handle/123456789/110393
dc.identifier.urnURN:NBN:fi:aalto-202110139582
dc.language.isoenen
dc.publisherAMERICAN CHEMICAL SOCIETY
dc.relation.ispartofseriesACS Applied Materials and Interfacesen
dc.relation.ispartofseriesVolume 13, issue 34en
dc.rightsopenAccessen
dc.subject.keywordelectrochemical impedance spectroscopyen_US
dc.subject.keywordelectrophoretic depositionen_US
dc.subject.keywordgalvanized steelen_US
dc.subject.keywordscanning vibrating electrode techniqueen_US
dc.subject.keywordwater-borneen_US
dc.titleBiopolymeric Anticorrosion Coatings from Cellulose Nanofibrils and Colloidal Lignin Particlesen
dc.typeA1 Alkuperäisartikkeli tieteellisessä aikakauslehdessäfi
dc.type.versionpublishedVersion
Files