Interfacial adhesion in metal/polymer systems for electronics

dc.contributorAalto-yliopistofi
dc.contributorAalto Universityen
dc.contributor.authorGe, Jun
dc.contributor.departmentDepartment of Electrical and Communications Engineeringen
dc.contributor.departmentSähkö- ja tietoliikennetekniikan osastofi
dc.contributor.labLaboratory of Electronics Production Technologyen
dc.contributor.labElektroniikan valmistustekniikan laboratoriofi
dc.date.accessioned2012-02-10T09:09:02Z
dc.date.available2012-02-10T09:09:02Z
dc.date.issued2003-12-05
dc.description.abstractThe effects of the different surface modification methods on the adhesion of electroless and sputter-deposited metals to dielectric polymers were investigated. The adhesion of Cu and Cr/Cu metallizations to the epoxies, liquid crystalline polymer and inorganic-organic hybrid polymer was measured with the newly developed pull test method. The microstructure and chemical state of the surfaces were characterized with the help of X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), atomic force microscopy (AFM) and contact angle measurements. The adhesion not only depends on the surface pretreatments but also the metallization techniques. The investigation revealed that plasma, reactive ion etching (RIE) and wet-chemical treatments induced clearly different physico-chemical changes on the polymer surfaces that strongly affected the adhesion of the metals to the polymers. The wet-chemical treatment produced large numbers of microcavities to anchor deposited electroless copper. The dependence of the adhesion on the surface roughness in the electroless copper/polymer systems confirmed the dominant role of the mechanical interlocking. The plasma and RIE treatments were very effective in improving the wettability of the polymer by increasing the surface polarity. It led to considerably better adhesion of sputter-deposited copper to the polymer than the chemical treatment. The enhancement of the surface polarity of the polymer and the enlarged surface contact area due to the increased roughness were the most important factors in the adhesion. SEM of the fracture surfaces showed that the failure modes of the copper/polymer systems were predominantly cohesive in nature within the polymer. By performing the theoretical and experimental investigations into controlling adhesion mechanisms in the metal/polymer systems, a better fundamental understanding of the adhesion between metals and polymers in the high-density built-up modules has been achieved.en
dc.description.versionrevieweden
dc.format.extent40, [55]
dc.format.mimetypeapplication/pdf
dc.identifier.isbn951-22-6784-5
dc.identifier.issn1457-0440
dc.identifier.urihttps://aaltodoc.aalto.fi/handle/123456789/2143
dc.identifier.urnurn:nbn:fi:tkk-001113
dc.language.isoenen
dc.publisherHelsinki University of Technologyen
dc.publisherTeknillinen korkeakoulufi
dc.relation.haspartGe J., Tuominen R. and Kivilahti J. K., 2001. Adhesion of electrolessly-deposited copper to photosensitive epoxy. Journal of Adhesion Science and Technology 15, No. 10, pages 1133-1143.
dc.relation.haspartGe J. and Kivilahti J. K., 2002. Effects of surface treatments on the adhesion of Cu and Cr/Cu metallizations to a multifunctional photoresist. Journal of Applied Physics 92, No. 6, pages 3007-3015. [article2.pdf] © 2002 American Institute of Physics. By permission.
dc.relation.haspartGe J., Turunen M. P. K. and Kivilahti J. K., 2003. Surface modification of a liquid-crystalline polymer for copper metallization. Journal of Polymer Science Part B: Polymer Physics 41, No. 6, pages 623-636.
dc.relation.haspartGe J., Turunen M. P. K. and Kivilahti J. K., 2003. Surface modification and characterization of photodefinable epoxy/copper systems. Thin Solid Films 440, No. 1-2, pages 198-207. [article4.pdf] © 2003 Elsevier Science. By permission.
dc.relation.haspartGe J., Turunen M. P. K., Kusevic M. and Kivilahti J. K., 2003. Effects of surface treatment on the adhesion of copper to a hybrid polymer material. Journal of Materials Research 18, No. 11, pages 2697-2707.
dc.relation.ispartofseriesReport series / Helsinki University of Technology, Laboratory of Electronics Production Technologyen
dc.relation.ispartofseries9en
dc.subject.keywordplasmaen
dc.subject.keywordsurfacesen
dc.subject.keywordetchingen
dc.subject.keywordX-ray photoelectron spectroscopyen
dc.subject.otherMaterials scienceen
dc.subject.otherElectrical engineeringen
dc.titleInterfacial adhesion in metal/polymer systems for electronicsen
dc.typeG5 Artikkeliväitöskirjafi
dc.type.dcmitypetexten
dc.type.ontasotVäitöskirja (artikkeli)fi
dc.type.ontasotDoctoral dissertation (article-based)en
local.aalto.digiauthask
local.aalto.digifolderAalto_63829
Files
Original bundle
Now showing 1 - 3 of 3
No Thumbnail Available
Name:
isbn9512267845.pdf
Size:
1.74 MB
Format:
Adobe Portable Document Format
No Thumbnail Available
Name:
article2.pdf
Size:
740.23 KB
Format:
Adobe Portable Document Format
No Thumbnail Available
Name:
article4.pdf
Size:
916.23 KB
Format:
Adobe Portable Document Format