Laser-Assisted Robotic Roller Forming of Ultrahigh-Strength Steel QP1180 with High Precision

dc.contributorAalto-yliopistofi
dc.contributorAalto Universityen
dc.contributor.authorMin, Junyingen_US
dc.contributor.authorWang, Jinchengen_US
dc.contributor.authorLian, Junheen_US
dc.contributor.authorLiu, Yien_US
dc.contributor.authorHou, Zeranen_US
dc.contributor.departmentDepartment of Mechanical Engineeringen
dc.contributor.groupauthorMaterials to Productsen
dc.contributor.organizationTongji Universityen_US
dc.date.accessioned2023-02-28T15:37:12Z
dc.date.available2023-02-28T15:37:12Z
dc.date.issued2023-02en_US
dc.descriptionFunding Information: This research was funded by Science and Technology Commission of Shanghai Municipality, grant number 21170711200 and General Motors collaborative research project, grant number GAC3599. Funding Information: Yi Liu would like to acknowledge the support from China Scholarship Council (Grant number: 202206260121). Publisher Copyright: © 2023 by the authors.
dc.description.abstractLaser-assisted forming provides a perfect solution that overcomes the formability of low-ductility materials. In this study, laser-assisted robotic roller forming (LRRF) was applied to bend ultrahigh-strength steel sheet (a quenching and partitioning steel with a strength grade of 1180 MPa), and the effects of laser power density on the bending forces, springback, and bending radius of the final parts were investigated. The results show that LRRF is capable of reducing bending forces by 43%, and a compact profile with high precision (i.e., a springback angle smaller than 1° and a radius-to-thickness ratio of ~1.2) was finally achieved at a laser power density of 10 J/mm2. A higher forming temperature, at which a significant decrease in strength is observed, is responsible for the decrease of forming forces with a laser power density of higher than 7.5 J/mm2; another reason could be the heating-to-austenitization temperature and subsequent forming at a temperature above martensitic-transformation temperature. Forming takes place at a higher temperature with lower stresses, and unloading occurs at a relatively lower temperature with the recovery of Young’s modulus; both facilitate the reduction of springback angles. In addition, the sharp bending radius is considered to be attributed to localized deformation and large plastic strains at the heating area.en
dc.description.versionPeer revieweden
dc.format.extent13
dc.format.mimetypeapplication/pdfen_US
dc.identifier.citationMin, J, Wang, J, Lian, J, Liu, Y & Hou, Z 2023, ' Laser-Assisted Robotic Roller Forming of Ultrahigh-Strength Steel QP1180 with High Precision ', Materials, vol. 16, no. 3, 1026 . https://doi.org/10.3390/ma16031026en
dc.identifier.doi10.3390/ma16031026en_US
dc.identifier.issn1996-1944
dc.identifier.otherPURE UUID: d42d1ab9-125f-41c3-a2eb-09c351863122en_US
dc.identifier.otherPURE ITEMURL: https://research.aalto.fi/en/publications/d42d1ab9-125f-41c3-a2eb-09c351863122en_US
dc.identifier.otherPURE LINK: http://www.scopus.com/inward/record.url?scp=85147841983&partnerID=8YFLogxKen_US
dc.identifier.otherPURE FILEURL: https://research.aalto.fi/files/101209867/materials_16_01026_v2.pdfen_US
dc.identifier.urihttps://aaltodoc.aalto.fi/handle/123456789/119908
dc.identifier.urnURN:NBN:fi:aalto-202302282246
dc.language.isoenen
dc.publisherMDPI AG
dc.relation.ispartofseriesMaterialsen
dc.relation.ispartofseriesVolume 16, issue 3en
dc.rightsopenAccessen
dc.subject.keywordlaser-assisted formingen_US
dc.subject.keywordsharp bending radiusen_US
dc.subject.keywordspringbacken_US
dc.subject.keywordthermo-mechanical modelen_US
dc.subject.keywordultrahigh-strength steelsen_US
dc.titleLaser-Assisted Robotic Roller Forming of Ultrahigh-Strength Steel QP1180 with High Precisionen
dc.typeA1 Alkuperäisartikkeli tieteellisessä aikakauslehdessäfi
dc.type.versionpublishedVersion
Files