Learning Centre

Gas sensing properties of nanocrystalline metal oxide powders produced by thermal decomposition and mechanochemical processing

 |  Login

Show simple item record

dc.contributor Aalto-yliopisto fi
dc.contributor Aalto University en
dc.contributor.author Kersen, Ülo
dc.date.accessioned 2012-02-10T08:56:39Z
dc.date.available 2012-02-10T08:56:39Z
dc.date.issued 2003-10-24
dc.identifier.isbn 951-22-6736-5
dc.identifier.issn 1456-6001
dc.identifier.uri https://aaltodoc.aalto.fi/handle/123456789/2111
dc.description.abstract The objective of this research, was the synthesis of LaFeO3 and SnO2 fine powders for the subsequent preparation of thick film gas sensors. On producing fine metal oxide powders, often it is not possible to ensure separation of the particles during the synthesis, resulting in the formation of highly agglomerated material. In addition, there are often high synthetic costs associated with the powders obtained by these methods. Thermal decomposition and mechanochemical processing methods were selected to produce fine metal oxide powders. Thermal decomposition of a heteronuclear complex is a simple and relatively cheap method. Heat treatment of La[Fe(CN)6] · 4H2O leads to single-phase perovskite-type LaFeO3 fine powders. Heating in the temperature range 600-750 °C causes fast crystallite growth of slightly agglomerated particles and X-ray diffraction analysis showed only the pattern of orthorhombic transition phase of LaFeO3 particles. A paste for the preparation of the LaFeO3 thick film coating was obtained by mixing of polyvinyl alcohol solution and decomposed powder in a ball mill for 1 h. It was determined that there are two factors important for gas sensing, concentration of surface metal ions [Fe3+], and the concentration of oxygen adsorptive sites [Vo(..)]. LaFeO3−δ thick film with small crystallites, promotes a more rapid NO2 gas reaction at the surface and allows an equilibrium state to be obtained at 350 °C. Mechanochemical processing (MCP) is selected as the second, low cost method of manufacturing of fine powders in a conventional ball mill. During milling, deformation, fracture, and welding of powder particles continuously occur. The chemical reactions are activated by the repeated ball-powder collisions. Most of the reports on MCP that have appeared to date, concern the use of high-energy mills. It is shown that it may be possible to produce fine powder particles using a centrifugal mill of the conventional type instead of high-energy one. Nanocrystalline SnO2 powder was produced by two different chemical reactions. The first reaction, initiated by ball milling, produces water and the second reaction does not produce water. It should be noted that water, produced by the chemical reaction during milling, has a considerable influence on the reactivity of surface. Milling of predetermined stoichiometric amounts of SnCl2 with Ca(OH)2 and K2CO3 in an excess of CaCl2 and KCl respectively, resulted in the formation of the desired mass of SnO. After heat treatment and removal of the salt, slightly agglomerated SnO2 particles were produced with a tetragonal phase, confirmed by X-ray diffraction pattern. A very narrow particle size distribution of the powder is observed. The response of the LaFeO3 thick film to NO2 gas is investigated in the temperature range 250-350 °C, where the surface reactions are moderately fast. On exposure to low concentrations of H2S gas in air in the range 20-50 ppm the SnO2 film, prepared from anhydrous powder has higher gas response than the film prepared from hydrated powder. en
dc.format.extent 33, [43]
dc.format.mimetype application/pdf
dc.language.iso en en
dc.publisher Helsinki University of Technology en
dc.publisher Teknillinen korkeakoulu fi
dc.relation.ispartofseries Report / Helsinki University of Technology, Department of Electrical and Communications Engineering, Laboratory of Electromechanics en
dc.relation.ispartofseries 71 en
dc.relation.haspart Kersen Ü., 2001. Microstructural and surface characterization of solid state sensor based on LaFeO<sub>3-σ</sub> oxide for detection of NO<sub>2</sub>. The Analyst 126, No. 8, pages 1377-1381.
dc.relation.haspart Kersen Ü., 2002. H<sub>2</sub>S-sensing properties of nanocrystalline SnO<sub>2</sub> powder produced by mechanochemical milling. Materials Science Forum 386-388, pages 633-638. [article2.pdf] © 2002 Trans Tech Publications. By permission.
dc.relation.haspart Kersen Ü., 2002. The gas-sensing potential of nanocrystalline SnO<sub>2</sub> produced by a mechanochemical milling via centrifugal action. Applied Physics A: Materials Science & Processing 75, pages 559-563. [article3.pdf] © 2002 Springer-Verlag. By permission.
dc.relation.haspart Kersen Ü. and Sundberg M. R., 2003. The reactive surface sites and the H<sub>2</sub>S sensing potential for the SnO<sub>2</sub> produced by a mechanochemical milling. Journal of The Electrochemical Society 150, No. 6, pages H129-H134. [article4.pdf] © 2003 The Electrochemical Society, Inc. By permission.
dc.relation.haspart Kersen Ü., 2003. The gas-sensing potential of nanocrystalline SnO<sub>2</sub> produced by different chemical reactions and milling conditions. Helsinki University of Technology, Laboratory of Electromechanics, Report 70, 15 pages. [article5.pdf] © 2003 by author.
dc.subject.other Materials science en
dc.title Gas sensing properties of nanocrystalline metal oxide powders produced by thermal decomposition and mechanochemical processing en
dc.type G5 Artikkeliväitöskirja fi
dc.description.version reviewed en
dc.contributor.department Department of Electrical and Communications Engineering en
dc.contributor.department Sähkö- ja tietoliikennetekniikan osasto fi
dc.subject.keyword thermal decomposition en
dc.subject.keyword mechanochemical processing en
dc.subject.keyword fine metal oxide powders en
dc.subject.keyword semiconductor gas sensor en
dc.identifier.urn urn:nbn:fi:tkk-000793
dc.type.dcmitype text en
dc.type.ontasot Väitöskirja (artikkeli) fi
dc.type.ontasot Doctoral dissertation (article-based) en
dc.contributor.lab Laboratory of Electromechanics en
dc.contributor.lab Sähkömekaniikan laboratorio fi
local.aalto.digifolder Aalto_63449
local.aalto.digiauth ask


Files in this item

This item appears in the following Collection(s)

Show simple item record

Search archive


Advanced Search

article-iconSubmit a publication

Browse

Statistics