Browsing by Department "Rakennustekniikan laitos"
Now showing 1 - 20 of 335
- Results Per Page
- Sort Options
- Puurakenteisten lisäkerrosten toteuttaminen betonielementtirunkoiseen asuinkerrostaloon
School of Engineering | Master's thesis(2013) Nordberg, KaiThe aim of this Master's thesis was to develop a wooden structure system suitable for building additional floors and to produce model solutions for this purpose. The thesis was made as a part of an international research group SmartTES by Aalto University. In this research group the aim has been to further develop the TES Energy Facade wooden renovation system and to develop a structural system for extensions in relation with TES facade renovation. Therefore a wooden based facade renovation in relation with extensions was also touched in this Master's thesis. This thesis was focused on how to realize two additional wooden floors structurally and how to integrate HVAC systems in structures in relation with extensions. The main target group was Finnish concrete element buildings from 1960'S and 70's. The characters of these original buildings cause limitations for building extensions and therefore these were studied in the beginning of the process. The structural realization of the additional floors was analysed with calculations as well as the connection to the original building. A model building was used to illustrate problems that may occur when planning extensions. The model solutions were however developed to generic solutions that would be suitable for most of the buildings in the target group. A so called worst case analysis was used in the research work to reach the generic results. By using this analysis the results and solutions formed in the planning process became universal to the other buildings as well. The characteristic structures and details specific just for extensions were studied. These kinds of details are mostly the joints and connections between the old and new building envelope and details where HVAC systems need to be integrated. In this thesis research the additional floors are suggested to be realized on a specific adjustment structure that will transfer the loads of the additional floors directly to the old concrete walls. That was used as a generic principle because usually the old roof structure cannot stand for the loads of two additional floors. Primarily the Kerto Ripa open and closed panels were studied as the adjustment structure. Comparative capacity calculations of these structures were made for different load distributions. By doing wind calculations for an extended building it was also found out that the stiffening walls in additional floors needs to be anchored to the old building. At the same time it was stated that the old concrete walls however don't need to be reinforced when installing two additional floors. The capacity of foundations was studied generally but not numerically. As a result of this thesis the generic model solutions from structural details and HVAC integrations were designed. - Algorithmic Advancements in Drive-by Inspection Methods Towards Intelligent Bridge Monitoring
School of Engineering | Doctoral dissertation (article-based)(2023) Lan, YifuSince conventional vibration-based structural health monitoring (SHM) methods typically require the installation of numerous sensors directly onto the bridge, the substantial costs associated with on-site sensor installation and maintenance have long rendered such technology an expensive option. Recently, an alternative approach referred to as the "drive-by bridge inspection method" has attracted scholarly attention. This method necessitates no instrumentation on the bridge; instead, it uses a few sensors positioned on the vehicle traversing the bridge, with the vehicle functioning as both an exciter and a receiver. It offers the possibility to efficiently monitor groups of bridges (particularly small and medium-sized ones), presenting an economically efficient solution to bridge health monitoring problems. While previous research on the drive-by method has yielded promising results, there are still some challenging problems and ample room for improvement before its engineering application. This thesis aims to propose algorithmic solutions to address the challenges faced by the current drive-by methods, successfully extracting bridge modal parameters and identifying damage. In terms of bridge modal parameters, two algorithms are proposed. Algorithm 1 extracts the bridge frequency as a common signal component in the responses of multiple sensors mounted on the vehicle. This method does not require specially designed vehicles or multiple cars, as in earlier studies, but instead utilizes a single ordinary vehicle, providing a practical solution. Algorithm 2 employs the Coherence-PPI (Prominent Peak Identification) method, which extracts the bridge frequency from the common vibrational components of multiple passes of the same vehicle. Rather than seeking to minimize differences, it encourages variability in drive-by measurements (e.g., varying vehicle parameters, avoiding traversing the same road surface) to filter bridge frequencies. It is particularly suitable for vehicles passing the same bridge multiple times (such as buses). In terms of damage identification, a data-driven algorithm based on an optimized AdaBoost-linear SVM is proposed (Algorithm 3), which accurately indicates bridge damage using only the raw vibration signals received from vehicles passing the bridge. To further improve damage identification accuracy and address certain limitations of drive-by measurements, such as noise and data redundancy, a time-domain signal processing algorithm for the raw vehicle accelerations is also proposed (Algorithm 4). The proposed algorithms have been validated through numerical simulations, laboratory experiments, and field tests on simply supported and continuous beam bridges using truck and bus models. The ultimate goal is to achieve a practical and intelligent bridge health monitoring system. - Alkusanat
A1 Alkuperäisartikkeli tieteellisessä aikakauslehdessä(2023) Niiranen, Jarkko - Alkusanat
A1 Alkuperäisartikkeli tieteellisessä aikakauslehdessä(2020) Niiranen, Jarkko - Alkusanat
A1 Alkuperäisartikkeli tieteellisessä aikakauslehdessä(2024) Niiranen, Jarkko - Allianssitoteutusmuodon vaikutus rakennushankkeen aikatauluun
School of Engineering | Master's thesis(2012) Törrönen, SakuConstruction projects are long-term projects which contain many different parties and challenges. The various parties form complex relationship networks with many interfaces. A wide range of contracts are needed in those interfaces, and the interfaces offer also a huge change of information to distort, which may cause critical misunderstandings. Among other things, these problems create a great amount of controversy to the construction industry and those controversies will reduce the productivity of projects in the whole field. Alliance has been studied relatively little in the world, even though it has been in use in Australia over two decades. In Finland few reports and master's theses has been published, and about five alliance projects are in progress. This master's thesis focuses on the impact of the alliance to a construction schedule as a whole. The focus is especially in the main schedule tasks and their placements in the whole construction process. The alliance schedule is compared to the schedule of the lump sum contracting and of the design and construct model. A project which is completed using the alliance model is faster than a project completed by the design and construct model or the lump sum contracting model. When comparing these models to the alliance model, the alliance model expects the project to have more collaboration and fewer conflicts in different interfaces. Results of this thesis are based mainly on a mix of a literature study, participatory research and an analysis part, which were verified in a workshop. Participants of the workshop were leading experts of the alliance model in Finland and they were also familiar with the whole construction process. One of the main conclusions was that the project planning phase is possible to shorten, because the alliance has a development phase where the project's objectives and the boundary conditions can still be specified among all the parties. Advantages of the development phase were also noticed in the flexibility of its duration, innovation sensitivity and integration of the group. - Altistumisolosuhdeluokkien yhteys työympäristöissä koettuihin haittoihin, oireisiin, ryhmätason terveystietoihin ja psykososiaaliseen työympäristöön
A4 Artikkeli konferenssijulkaisussa(2019) Tähtinen, Katja; Lappalainen, Sanna; Karvala, Kirsi; Lahtinen, Marjaana; Remes, Jouko; Salonen, Heidi - Ämmässuon kaatopaikan laajennusalueen huoltotunneli ja sen geotekninen mitoitus
School of Engineering | Master's thesis(2008) Winqvist, FredrikPääkaupunkiseudun yhteistyövaltuuskunnan jätteenkäsittelykeskuksessa Ämmässuolla vastaanotetaan pääkaupunkiseudun yhteensä yli miljoonan asukkaan ja 50 000 yrityksen jätteet. Ämmässuon jätteenkäsittelykeskus on pohjoismaiden suurin yhdyskuntajätteen kaatopaikka. Jätteenkäsittelykeskuksen vanha jätetäyttöalue oli suljettava viranomaispäätösten (VNp 861/97 ja 1049/99) määräyksiin perustuen viimeistään 1.11.2007. Vanhan täyttöalueen länsipuolelle sijoittuvan laajennusalueen suunnittelu on aloitettu vuonna 1990 ja sen ensimmäinen täyttöalue vihittiin käyttöön 30.10.2007. Laajennusalueelle tuleva jätetäyttö eristetään ympäristöstään tiivisterakenteiden avulla. Tiivisterakenteeseen kuuluu kaatopaikan pohjan kuivatuskerros, joka koostuu vettä hyvin läpäisevästä materiaalista ja suotoveden keräilyputkista. Tehokkaan kuivatuksen varmistamiseksi on Ämmässuolla päädytty ratkaisuun, jossa pohjarakenteet salaojineen kallistetaan alueen keskiosaan päin viettäviksi. Keskiosaan on rakennettu täytön alle jäävä teräsbetoninen huoltotunneli, jossa sijaitsevaan kokoojaputkistoon salaojat yhdistetään. Kokoojaputkien avulla salaojavedet johdetaan täyttöalueen eteläpuolelle, josta ne edelleen siirretään käsittelyyn. Koska Suomessa ei ole aikaisempia kokemuksia vastaavan huoltotunnelirakenteen suunnittelusta ja toteutuksesta, suunnittelun lähtöaineiston keräämiseksi selvitettiin olemassa olevat huoltotunnelikohteet maailmanlaajuisesti. Kaikki 13 todettua huoltotunnelikohdetta sijaitsevat Euroopassa, joista pääosa Saksassa. Ämmässuon huoltotunnelin poikkileikkauksen dimensiot määritettiin huonetila- ja rakennemitoituksen avulla. Muotoa valittaessa huomioitiin myös käytössä oleva muottitekniikka. Rakennemitoituksen lähtökohdaksi tehtiin maapainelaskelmia, joilla selvitettiin huoltotunnelin rakenteisiin kohdistuva maanpaine jätteen tilavuuspainon vaihdellessa välillä 12...15 kN/m3. Käytetty jätetäyttösyvyys perustuu ympäristöluvan asettamiin reunaehtoihin. Jätetäyttösyvyytenä laskelmissa käytettiin 70 metriä. Huoltotunnelin suunnittelussa käytetty mitoitusikä oli 200 vuotta. Maanpainelaskentojen lisäksi tarkasteltiin siirtymärakenteiden tarvetta painumaerojen aiheuttaessa lisärasituksia suoto- ja tarkkailusalaojiin sekä geomembraaniin huoltotunnelin seinälinjalla. Ämmässuon huoltotunnelin 1. rakennusvaiheen työt käynnistyivät kesäkuussa 2006 ja valmistuivat lokakuussa 2007. Huoltotunnelin ensimmäisen vaiheen pituus on 450 metriä. - Puurakenteisen pientalon rakennusosien välisten liitosten lämpö- ja kosteustekninen tarkastelu
School of Engineering | Master's thesis(2013) Salmi, KaisaThe new regulations and guidelines of energy management in buildings in the National Building Code of Finland became effective in July 2012. The new build requirements of the European Union Energy Performance of Buildings Directive were taken into account in the renewal of the regulations. The linear thermal bridges of building element junctions were included in the regulations of energy management in buildings. The aim of this thesis was to give recommendations of building element junctions which reduce total heat loss and are technically well-functioning in their heat and moisture behaviour. This study examines the heat behaviour of building element junctions in a wooden one-family house by determining the linear thermal transmittance values. These values were compared to the present default values of the National Building Code of Finland. The mould growth risk of the building element junctions were examined with the mathematical model of mould growth. The Comsol Multiphysics 4.3 program was used to numerically examine the calculation models of this study. In examining the linear thermal transmittance value, the junction alternatives were modelled in a three-dimensional calculation model. When assessing the mould growth risk, two and one-dimensional models were used. The study examines junctions between the external wall and the roof, the external wall and the intermediate floor and the external wall and the base floor. Also the external wall outside and inside corner junctions were examined. These were the five basic junction types. By varying the material and thickness of sheathing board, the spacing of the intermediate floor primary and secondary beams, and the material of the base wall structure of the base floor, a total of 99 different junction alternatives were created. The junction alternatives with the external wall construction type with the smallest coefficient of thermal transmittance proved to be the most efficient regarding to the total heat loss. The results of this study show that when calculating total heat loss and total energy consumption of new buildings, it is possible to use the linear thermal transmittance default values of the National Building Code of Finland or the junction specifically defined values obtained as the result of this study. The results further show that the effect of the linear thermal transmittance to the E-factor of the building is quite small and the present default values of the National Building Code of Finland are good to begin with. Determining the specific linear thermal transmittance values of building element junctions in new building should be considered case by case due to the large amount of work related to this task. - Asfalttipäällysteen tyhjätilan mittausmenetelmien arviointia - Vuosien 2016 ja 2017 koetiemittausten ja tutkimusten tulokset
School of Engineering | D4 Julkaistu kehittämis- tai tutkimusraportti tai -selvitys(2018) Pellinen, Terhi; Eskelinen, Pekka; Hartikainen, Ari - Assessment of air void content of asphalt using dielectric constant measurements by GPR and with microwave radar
School of Engineering | D4 Julkaistu kehittämis- tai tutkimusraportti tai -selvitys(2016) Pellinen, Terhi; Eskelinen, Pekka; Hartikainen, Ari; Huuskonen-Snicker, Eeva; Eskelinen, JussiIn this report, we have presented microwave radar and GPR measurements as well as laboratory tests conducted in 2014-2016. The microwave radar was tested in three different construction sites. In addition, GPR measurements were obtained for comparison. Laboratory tests included traditional density measurements and 7-17 GHz VNA scanning of drill cores obtained from the test sites. A new laboratory measurement method using cavity resonator principle was introduced with promising results. Testing of this new method will be continued. The results indicate no clear correlation between air void content and GRP permittivity measurements. Permittivity is sensitive to the changes in the relative permittivity of aggregates and volume portions of aggregates and bitumen. The relative permittivity of the aggregates determines the base level for permittivity measured with radar or VNA. In the course of this research, it has become apparent that a new calibration procedure for the GPR measurements is needed. The aim in further research is to extract core samples from pavement areas with different densities to obtain a local calibration model. - An assessment of distributed building information management systems
School of Engineering | Master's thesis(2013) Kuokkanen, JyryCollaboration between different disciplines is a central part of any construction project. When new building information modelling (BIM) tools are replacing traditional document based workflows, collaboration can and has to change too. Building information already enables better information management for all stakeholders in the process, but the collaboration has not matured yet. Interoperability between individual applications works to some extent but more generic collaboration is still a challenge. Improving BIM-based collaboration has been one of the most important research questions and a target for further development both in Finland and globally. Different solutions have been suggested but they have not proved to be sufficient for the needs of different stakeholders. This research assesses new approaches for BIM-based collaboration. One of the main objectives is to explain distributed information management. Thus, the relationship compared to other BIM-collaboration platforms can be understood. Relations between partial models which are used as a reference model by publishing and subscribing the models of other stakeholders, create the base for the concept. Instead of having one object presenting all disciplines and their design intents in integrated centralized system, the models are not integrated. There are created relations between models and objects to maintain the consistency of the data. The semantic web as the proposed technical solution can provide many advantages fulfilling some requirements for BIM collaboration platforms. The assessment of the system is done by evaluating how applicable the general requirements for collaboration platforms are and how the new concept fulfils them. Retaining the information distributed by the authors has many advantages, but it creates some new requirements that have to be considered when the concept is developed further. Furthermore, current workflows were investigated by interviews and a workshop. The workflows create some requirements that the new information management system needs to support as well. The concept is in an early stage and there are no practical solutions that could have been used to test the system. Therefore, the real value is difficult to assess, but based on the research it can solve many of the problems current platforms have. However, the concept still requires more research and practical testing. This thesis suggests that the results of the assessment should be considered as the concept is developed further. In addition the whole concept of collaboration could be rethought and typologies could be generated accordingly. - Asuinalueen parannusopas
School of Engineering | D4 Julkaistu kehittämis- tai tutkimusraportti tai -selvitys(2012) Junnonen, Juha-Matti; Karhu, JessicaTämä Asuinalueen parannusopas on Rakennusteollisuus RT:n koordinoiman Ketterä-tutkimushankkeen loppuraportti. Raportin tavoitteena on tuoda esiin näkökantoja ja menettelytapoja, joita voidaan hyödyntää asuinalueen parantamisessa ja kehittämisessä. Tutkimushankkeen primäärisenä tavoitteena oli kehittää asukasymmärrykseen perustuva asuinalueiden korjausmalli. Pääpaino oli siten alueiden fyysisen ympäristön parantamiseen liittyvissä näkökulmissa. Lisäksi hankkeen tavoitteina oli parantaa asunto-osakeyhtiöiden hallitusten jäsenten tietoisuutta niin korjausvaihtoehdoista kuin niiden kustannuksista ja saavutettavista hyödyistä sekä tukea asunto-osakeyhtiöiden päätöksentekoa korjaushankkeiden käynnistämisessä. Tutkimushankkeen tarkastelukohteena oli Helsingissä sijaitseva Siltamäen asuinalue, joka koostuu vuosina 1968-1974 rakennetuista asunto-osakeyhtiöistä. Alueen rakennukset ovat jo teknisesti vanhentuneet, erityisesti LV-järjestelmät sekä julkisivut ovat teknisen käyttöikänsä lopussa. Myös alueella oleva ostoskeskus on rakenteellisesti erittäin huonossa kunnossa. Asunto-osakeyhtiöissä osakkaat joutuvat itse rahoittamaan vaadittavat korjaukset vaikka valtio on tukenut viime vuosina esimerkiksi energiakorjauksia. Mahdollisia rahoitusvaihtoehtoja ovat perinteinen yhtiökohtainen lainoitus, yhtiövastikkeilla kerätyt ennakkosäästöt tai omaisuuden, kuten rakennusoikeuden, myyminen lisä- ja täydennysrakentamiselle. Varsinainen korjaushanke voidaan toteuttaa monella eri tavalla. Toteutusmuodon valinnassa keskeistä on pohtia millainen toteutusmuoto täyttää tilaajan hankkeelle asettamat tavoitteet, sillä eri toteutusmuodoilla on erilaiset riskiprofiilit ja niiden ominaisuudet tukevat vaihtelevalla tavalla tavoitteiden saavuttamista. Tilaajana voi toimia yksittäinen taloyhtiö tai taloyhtiöiden muodostama yhteenliittymä. Keskeistä asuinalueen parantamisessa on, että alueen taloyhtiöt tekevät keskenään tiivistä yhteistyötä hankkeen muodostamisessa. Alueellisella yhteistyöllä on mahdollista vaikuttaa hyvin voimakkaasti asuinalueen parantamiseen ja kehittämiseen yhteisen vision ja tahtotilan mukaisesti. Ilman yhteistä visiota ja tahtotilaa, koko alueen parantaminen jää väistämättä takaalalle kunkin taloyhtiön keskittyessä vain oman yhtiön rakenteellisiin korjauksiin. Yhteisesti muodostettu visio ja sen täyttämiseksi tehtävä ponnistus tuo myös yhteisiä etuja ja hyötyjä niin yksittäiselle osakkaalle, taloyhtiölle kuin myös yhteiskunnalle sekä ympäristölle. - Asukaspalvelujen uudet yrityslähtöiset organisointimallit
School of Engineering | D4 Julkaistu kehittämis- tai tutkimusraportti tai -selvitys(2014) Henttonen, Anu; Puhto, Jukka; Junnonen, Juha-MattiResident services are provided to residents either in the apartments or in the residential building to support the housing and performing housework. Even though the demand for resident services has been recognized, the current supply and organization models for providing resident services are still undeveloped, and there are various challenges related to the supply. The target of the research was to create a better understanding of operational environment related to the organization models of resident services, which was considered from the housing business players' point of view. The study comprised a literature review. Current supply models as well as challenges and success factor of developing new organization models were investigated in a qualitative interview study, in which 21 interviewees including real estate owners, property managers, property maintenance companies, and domestic services companies were interviewed. The most used services according to the literature view were similar to the most important ones according to the interviewees. Almost all the services are more used in older age groups, which were also regarded as the most important client segment for resident services in the interview study. The supply of resident services is very scattered since there are property managers, property maintenance companies, resident services and nursing services companies, municipalities, residents, communities, and third sector providing resident services. In the current organization models, residents have the main responsibility for procurement of resident services. Even though most of the interviewees predicted a significant increase in demand for resident services in next five years, rare companies had started any actions in order to develop supply models. Tax credit for domestic costs was regarded as a critical factor for the whole resident services market. Competition with the black market and help from relatives and neighbors were considered as demand-driven challenges. The substantial amounts of clients with small and scattered orders, responsibility issues related to consumer business, difficulty of standardization and issues to pro-vide services with reasonable prices profitably were highlighted as challenges related to the developing organization models. In order to establish profitable models, the organization model needs to be lightly organized and directed to a sufficient amount of residents. Other success factors are suitable design solutions of residential building, exploitation of web-based tools and active areal marketing. Based on the empirical data, following six potential models for supply of resident services were composed. - Asumisen ja hyvinvoinnin uudet palvelumallit
School of Engineering | D4 Julkaistu kehittämis- tai tutkimusraportti tai -selvitys(2013) Huuskonen, Arto; Siltaloppi, Jaakko; Puhto, JukkaJulkaisu on vuonna 2010 käynnistyneen ALMA-tutkimushankkeen (Asumisen ja hyvinvoinnin uudet palvelumallit) Aalto-yliopiston, BES-tutkimusryhmän tutkimusosuuden loppuraportti. ALMA-tutkimushankkeessa tarkastellaan asumiseen ja hyvinvointiin liittyvän palveluliiketoiminnan haasteita ja edellytyksiä sekä luodaan keinoja uusien palvelumallien tuottamiselle. Erityisesti tutkimuksessa on keskitytty asumissektorin toimijoiden verkottuneisiin toimintamalleihin ja yhteistyösuhteiden johtamiseen asukas- ja kiinteistöpalvelujen tuottamiseksi ja kehittämiseksi. Raportti koostuu kahdesta itsenäisestä osakokonaisuudesta: Osa 1 ”Asumispalvelut ja niiden kehittäminen” tuo esiin palveluiden kysyntään ja kehittämiseen liittyviä näkökulmia. Osassa luodaan katsaus keskeisiin asukaspalvelujen kehittämisen haasteisiin suomalaisella asumissektorilla sekä esitellään erilaisia malleja uusien palvelujen kehittämiseksi. Osan kirjoittamisesta on vastannut tohtorikoulutettava Jaakko Siltaloppi. Osa 2 ”Verkostojohtaminen palveluliiketoiminnassa” avaa verkostomaisen toiminnan edellytyksiä ja toimintamekanismeja asumisen palveluverkostoissa, erityisesti informaation ja tiedon johtamisen näkökulmasta. Osassa selvitetään ja vertaillaan palveluverkostojen johtamisen mekanismeja vakiintuneissa kiinteistöpalveluverkostoissa sekä nousevissa senioriasumiskonseptien kehittämiseen tähtäävissä kumppanuuksissa. Tutkimuksen tuloksena esitellään malli informaation ja tiedon johtamiselle palveluverkostoissa. Osan kirjoittamisesta on vastannut tohtorikoulutettava Arto Huuskonen. Hankkeen Aalto-yliopiston tutkimusosuudesta on vastannut tutkimuspäällikkö Jukka Puhto. Tutkimushanke on toteutettu yhteistyössä Tampereen teknillisin yliopiston Asumisen liiketoiminta –tutkimusryhmän (ASLI) kanssa. Hankkeen yhteistyöorganisaatiot ovat Helsingin kaupungin talous- ja suunnittelukeskus, Tampereen kaupungin asuntotoimi, Asokodit Oy, ISS Palvelut Oy, Järvenpään Mestariasunnot, Realia Isännöinti Oy, Sato Oyj, sekä Suomen Aluerakennuttaja Oy. Hankkeen viestintäpalvelujen tuottamisesta on vastannut Oy Culminatum Ab. - Asumisen palvelukonseptit - Palvelukonseptin kehittämisen prosessimalli
School of Engineering | D4 Julkaistu kehittämis- tai tutkimusraportti tai -selvitys(2011) Aaltonen, Alexander; Siltaloppi, Jaakko; Puhto, JukkaLänsimaisissa talouksissa palvelujen kansantaloudellinen merkitys on kasvanut merkittävästi viimeisten vuosikymmenten aikana, ja tällä hetkellä keskimäärin kaksi kolmasosaa bruttokansantuotteesta syntyy palvelusektorilla. Palvelujen merkityksen kasvuun vaikuttavat merkittävät yhteiskunnalliset muutostrendit kuten väestön ikääntyminen ja elämäntapojen muutos, joiden vuoksi myös asumisessa tullaan tulevaisuudessa näkemään uudenlaisia palvelukonsepteja. Tämän tutkimuksen tavoitteena oli selvittää, mistä tekijöistä palvelukonsepti rakentuu ja miten uusia palvelukonsepteja voidaan kehittää. Lisäksi tutkimuksessa vertailtiin olemassa olevia asumiseen liittyviä palvelukonsepteja Suomessa ja Yhdysvalloissa. Tutkimuksen ensimmäisessä osassa kartoitettiin kirjallisuuden perusteella palvelukonseptiin liittyviä sisältöjä ja merkityksiä. Lisäksi ensimmäisessä osassa selvitettiin aikaisemmassa tutkimuksessa esiintyviä lähestymistapoja palvelukonseptin kehittämisen prosessiin. Tutkimuksen toinen osuus toteutettiin empiirisesti keräämällä tietoa suomalaisista ja yhdysvaltalaisista asumiskonsepteista ja niihin liittyvistä palvelusisällöistä hyödyntämällä yritysten Internetsivustoja. Tarkastelun kohteena olivat pääasiallisesti suuret asuinkiinteistöjen omistajat sekä asumissektorilla toimivat rakennusliikkeet. Suomalaisissa asumiskonsepteissa palveluja esiintyy vaatimattomasti. Erityisesti asumisen tukea ja lisäarvoa tarjoavien, asukkaille suunnattujen asukaspalvelujen tarjonta on vähäistä. Asumispalvelut liittyvätkin tällä hetkellä pääosin erityisryhmien kuten ikäihmisten asumiseen, sekä joissain tapauksissa myös ylelliseen asumiseen. Ylelliset asumisen konseptit ovat kuitenkin huomattavasti tyypillisempiä Yhdysvalloissa, jossa erilaisia lisäpalveluja ja mukavuuksia on kytketty asumiseen monipuolisesti. Asumiseen liittyvät palvelusisällöt ovatkin Yhdysvalloissa huomattavasti Suomen vastaavia pidemmälle kehittyneempiä. Tutkimuksen tuloksena kehitettiin malli asumisen palvelukonseptin kehittämiselle. Mallin päävaiheet ovat palvelustrategian laatiminen, idean kehittäminen, palvelukonseptin kehittäminen, palvelun suunnittelu, täysmittainen kaupallistaminen ja lanseeraus sekä jälkiarviointi. Malli perustuu kirjallisuudesta tehtyihin havaintoihin palvelukonseptin määrittelystä sekä uuden palvelun kehittämisen prosessimallista, ja mallia tuotiin lähemmäksi asumisen kontekstia ottamalla huomioon empiirisessä tarkastelussa esiin nousseita tekijöitä käytännön asumiskonsepteihin liittyen. - Asumista tukevien palvelujen kehittäminen
School of Engineering | D4 Julkaistu kehittämis- tai tutkimusraportti tai -selvitys(2013) Wiinikka, Tytti; Junnonen, Juha-Matti; Puhto, JukkaAsumiseen liittyy nykyään suuria muutospaineita, ja asuminen onkin murrosvaiheessa. Muutospaineet kumpuavat kahtaalta; asukkaista ja asukkaiden preferensseistä johtuvista tekijöistä, jotka muuttavat asumiseen kohdistuvia kysyntätekijöitä sekä teknologisista tekijöistä, jotka mahdollistavat uudentyyppisiä lähestymistapoja asumiseen liittyvien palveluiden tarjontaan. Tämän tutkimuksen tarkoituksena on hahmottaa asumista tukevien palveluiden kehittämisen edellytyksiä ja suuntaviivoja, joiden avulla tuetaan ja helpotetaan kaikkien ikäryhmien asumista ja toimimista. Erityisesti ikääntyville asumista tukevat palvelut ovat keskeisiä, mutta tässä tutkimuksessa ei rajauduta yksinomaan ikääntyneisiin tai heidän tarpeisiin. Hyvin järjestetyillä palveluilla voidaan kuitenkin edesauttaa ikääntyvien ihmisten kotona selviämistä entistä pidempään. Tutkimuksen tuloksia on mahdollista hyödyntää myös yleisemmin asumista tukevien palveluiden kehittämisessä sillä usein ikääntyville tarkoitetut asumista tukevat palvelut on laajennettavissa myös esimerkiksi lapsiperheiden asumiseen. Keskeiset tutkimuskysymykset olivat: a) Mitkä tekijät vaikuttavat lähiön palvelujen kehittymiseen? b) Millainen rooli toimijoilla on asuinalueiden kehittymisessä palvelujen näkökannalta? c) Miten lähiöiden palvelurakenteen kehittymistä voidaan edesauttaa? Tutkimus tehtiin tapaustutkimuksena, jossa case-alueena käytettiin Jakomäkeä. Aineisto kerättiin tilastoista ja asiantuntijahaastatteluilla. Haastatteluista nostettiin esiin teemoja, jotka asiantuntijat kokivat olennaisiksi palvelujen kehittämisen näkökulmasta. Asumista tukevien palvelujen kehittäminen vaatii monialaista osaamista ja ymmärrystä kokonaisuuksista. Vain yksi organisaatio tai taho ei pysty kehittämään palveluja tehokkaasti. Kun puhutaan alueellisista palveluista, niiden kehittäminen vaatii vielä enemmän monialaista osaamista ja ymmärrystä alueen historiasta ja asukkaiden tarpeista. Tästä syystä toimiva yhteistyö ja kokonaisuuksien hallinta on olennaista, kun lähdetään kehittämään uusia palveluita. Jatkossa kannatta pohtia sitä, mikä sektori on tehokkain alueen kehittäjä ja palvelujen tuottaja. Kiinnostavia jatkotutkimuksen aiheita ovat implementoinnin haasteet sekä alueaktiivisuus ja juuri paikallisten toimijoiden toiminta - Attitudes and behaviour of residents within the framework of energy efficiency
School of Engineering | Doctoral dissertation (article-based)(2013) Valkila, NooraThe goal of this study was to determine how Finnish energy policies are realised and the attitudes of consumers regarding energy issues. Further research was done to study if the attitudes of residents and their behaviour regarding energy issues are inter-related. A goal was also to study if place of residence affects attitudes and behaviour. Are residents willing to improve their efficiency in terms of energy consumption? The range of applied research methods was diverse. A literature review was performed and experts operating in the energy industry were interviewed. Ordinary energy consumers, i.e. residents, were studied using interviews and measurements and by forming consumer panels. Content analysis and statistical methods were used for analysing the results. Based on this study, Finland should strive to utilise more diverse energy sources and engage in closer co-operation with different stakeholders. Resident attitudes on energy matters must be influenced. The most effective influencing methods are peer groups, communication, media, training and education, perceptions and visions. Age and the location of residence influence people's attitudes and behaviour with respect to energy issues, whereas their life satisfaction level does not. For example, research subjects that reside in a more densely populated suburban area are more concerned with climate change and more willing to give up driving than research subjects that live in more scarcely populated residential areas. Residents are willing to improve their energy behaviour, although young and elderly people are more willing to make environmentally friendly choices than the middle-aged demographic. There is a gap that needs to be bridged between attitudes and behaviour. If the attitudes of residents were to become more active and positive towards energy, they could lead to the desired energy-efficient behaviour. This study does not aim to make generalisations regarding Finns. Instead, it wishes to explain the energy-efficiency phenomena with respect to attitudes and behaviour within a Finnish context. - Ydinvoimalaitoksen reaktorirakennuksen jännitetyn suojakuoren suunnitteluperusteet Suomessa
School of Engineering | Master's thesis(2013) Knuutila, Miska - Tietomallintamisen hyödyt ja haasteet rakennushankkeen eri osapuolten näkökulmasta
School of Engineering | Master's thesis(2011) Korpela, Jenni o.s. PalomäkiThe aim of this study is to find out the benefits and problems of using building information modelling. The target of the research was a life-cycle project in Kuopio by Lemminkäinen PPP Oyj. The data of the study is based on interviews of participants of a construction project. The problems of building information modelling were interpreted by activity theory and found out the contradictions affecting in activity. Activity theory is a theory, which illustrates activity of a person or group, and in where contradictions play a significant role when improving activity. Results of interviews were compared to benefits and problems of building information modelling presented in literature. Main benefits in the interview were perspicuity of model, the quantitative information and list, and use when checking plans. On the other hand, participants in interview told about problems which they had with modelling. Models and paper plans were not synchronized of information was missing. In literature, one benefit of BIM was improved design quality. The clash detection, which BIM enabled, was not really used. On the other hand, designers thought that when modelling, they had to do more work than in usual design process. Based on the problems, an interpretation of contradictions was made. The main contradictions were connected to activity of designers. Designer hadn't had enough information and resources to start their job. Also, their opinions about information included in the model differed from the opinions of the persons in the site. There wasn't also enough communication between designers. To solve these contradictions, it must be agreed, what information must be included in the model and how to do checking of the plans. In addition, it must be confirmed, that every designer has all the information and resources he needs to complete his job. To improve the cooperation between designers, developer needs better leading and meeting policy. The process must be more transparent, so that designer can reserve enough resources and insist information from other designers. The participants of the project accepted to try Last Planner-method, which can help to identify the requirements of work and to fix the target of the near future.